Dual Support / Off-The-Shelf / 700 Series / XD759-HYD

XD759-HYD

Load Rating: 800 lbs

Swing Radius: 48"

Height Range: 46.9” – 58.7”

Max Torque: 5,400 in-lbs

Easy Crank: 2,000 in-lbs

The Model XD759-HYD-IND15-P8-B072 shown is typical and representative of the XD759-HYD Models.

To receive a CAD model or a quotation:

Configure a Flotron Fixture
The maximum distance between mounting interfaces is directly related to the main beam length. Specify the distance between mounting interfaces to be at or slightly larger than the length of the part-to-be-handled. The fixture can be adjusted to accommodate smaller length parts, however, the main beam(s) extending from each end frame may be inconvenient. For more information see the 700 SERIES OPTIONS page and 700 SERIES CREATING A MODEL NUMBER pdf.
Addition of the optional SR or DR gearbox decreases the vertical riser adjustment from 12" to 10" and increases the minimum trunnion height from 46.7" to 48.7".
A smaller than standard swing radius may be recommended for some applications. See the "Technical Section" under "Holding Fixture Safety" on page 3 of 7 concerning "Unexpected Accident Loads" and the chart on page 4 of 7 referring to "Maximum Recommended Swing Radius"

Product Features

  • Safety Factor: 3 for Yield & 5 for Ultimate
  • Rated Load Capacity:
    • Dynamic, 0″ eccentricity: 800 lbs. (363 kg.)
    • Dynamic, 5″ eccentricity: 800 lbs. (363 kg.)
    • Note: The hydraulic cylinders are single acting and a minimum load of 150 lbs is recommended to activate the return (compression) stroke and to give good synchronization of the risers.
  • Operating Temperature: +32 to +104 °F (0 to +40 °C)
    • Contact factory for special applications with extended operating temperatures.
  • Trunnion Interface/Mount/Clamp Options:
    • Angle Interface
    • Mounting Plate Interface
  • Materials: Steel construction
  • Finish: Flotron Blue powder coat with selected parts zinc plated.
  • Gearbox: 5″ diameter x 2″ wide wheel with polyurethane tread, sealed swivel bearing and Tech-lock brake
  • Choice of Main Beam Length
  • Main Beam Ball Lock Pins: Reliably prevents End Frames from slipping on Main Beams
  • Casters: 5″ diameter x 2″ wide wheel with polyurethane tread, sealed swivel bearing and Tech-lock brake
  • Synchronized Hydraulic Risers: The hydraulic risers can adjust the height of the part-to-be-handled while it is attached to the trunnion interfaces. Turning the pump crank clockwise or counter-clockwise causes the risers to raise or lower in unison.
  • A smaller than standard swing radius may be recommended for some applications. See the “Technical Section” under “Holding Fixture Safety” on page 3 of 7 concerning “Unexpected Accident Loads” and the chart on page 4 of 7 referring to “Maximum Recommended Swing Radius”
  • Optional Main Beam Lengths
  • Optional Trunnion Interface/Mount/Clamp
  • Optional Index Plate
  • Optional Index Stops
  • Optional Casters & Leveling Jacks
  • Optional Gearboxes incorporating heavy duty, low backlash and stairstep resistant features
  • Optional finishes for clean room compatibility
  • Optional Ground Lug and Drag Chain for use in electrostatically protected areas (EPA’s)
View 700 Series Options

As Flotron is constantly improving products and methods of manufacturing, we reserve the right to modify and/or change design or specifications without notice. Please contact Flotron for verification of critical dimensions and specifications.

For 700 Series - Creating a Model Number pdf click here.

For clarification of terms or phrases, please see the Holding Fixtures Definitions page.